Starter Crack Master Windshield Chip and Crack Repair Kit

Description

Repair Chips and Long Cracks with One Simple Windshield Repair Tool
Repair Chips and Long Cracks
Easy system to learn and use -over 90% of users learn by video and manual
No need to walk away from long cracks that pays you 0 +
Stronger than a new windshield
Passes the same Federal Motor Vehicle Safety Standard tests as a new windshield
Passes the Repair of Laminated Auto Glass Standard  (ROLAGS)
Ultra Bond was used by State Farm to prove to a Supreme Court that windshield repair was as strong as new glass.
Two Wonder Bars give you four tool options
Don't walk away from 0 Plus
Starting a new business or adding windshield repair to your current business, you need to make money on every opportunity you come across.  With the Ultra Bond starter kit you can repair chips (Stone-breaks) and long cracks too. If you repair just chips you will no doubt run into long cracks every day. If you don't repair them you just lost 0 +. Did you know that over 90% of consumers will choose a long crack repair over a replacement? Not only because it costs hundreds less but only takes less than 30 minutes. A repair is also far safer than a replacement. A repair does not alter or compromise the many safety systems that are connected to the windshield such as the airbag, roof crush, occupant retention, impact and penetration protection from road debris, occupant ejection and the newer vehicles with ADAS (Advanced Driver Assist Systems) must be re-calibrated if the windshield is replaced which costs more money and more time for the consumer. Often the consumer after a  replacement must then go to the car dealer for re-calibration of the ADAS. Protect you customers vehicle safety features by doing a repair.
The Crackmaster Bridge structure splits apart into two long crack repair tools - a long crack slider and a crack opener.
See the
next size up Standard Repair Kit
for only 0 more for many more Wonder Bar Tool options.
Starter Windshield Crack Repair Kit Wonder Bar Tool Options:
See the new Wonder Bar explained and assembled in this
video
:
(1) Crack Master Bridge
Repair Chips and Long Cracks with one tool
6-in-1 Tool - Has six different tool configurations
Performs eight different functions
Cost per chip repair of 8 cents
Most efficient chip repair tool on the market
Most effective long crack repair tool ever made
Sets-up in seconds
No break-down after repair
Refills in seconds; can do 15-20 chip repairs before refilling is needed
Controlled flexing, compression and tension
Does not waste any resin; your cost per repair is at least 300% less than other tools on the market
Completely fills most chips in less than 60 seconds
This NEW two Wonder Bar bridge type holding structure offers perfect compression, leveraging, mechanical advantage with no tension from the suction cups. The Quick-Turn Stainless Steel Injector creates a windshield repair tool that is perfect. It holds 36 drops of resin, which means you can load it and not have to re-load for days which saves time, money and work. Uses
300% less resin
than most systems. Most systems waste as much resin as they use by having to refill after each repair. Your cost per chip repair is 8 cents. You will get 300 chip repairs from one bottle of our resin with this tool.
Most systems you have to take apart and re-load for every repair (set-up and break-down) . When you finish with other tools you will have resin running down the windshield when you remove it or you will be dumping what is left in the injector. You then have to refill again and go through set-up for your next repair. You will waste more resin than you injected into the break. Our system sets-up in seconds and break-down is just removing the tool off the glass. Our injector can do up to twenty repairs without having to re-load - semi-automatic.  It also has 27 inches hg of available vacuum. Perfect size, placement and durometer suction cups will prevent flowering and gives you maximum control of pressure/compression for flexing of the glass.
The Holding Structure or bridge holds the injector in place while repairing a stone-break/chip or long crack. But the holding structure is much more than that; the structure controls pressure both on the resin injection and the pressure on the glass. Compression (pushes down)  flexes a stone-break open so that the resin will efficiently fill every leg and crater within the break. On a long crack which is surfaced it must be minimal. The physics of this structure are perfectly balanced so that a stone-break is flexed open so that
70% of chips are completely filled and ready to be cured in less than 60 seconds.
Our long crack repairs are stronger than a new windshield.
The proper two suction cup placement (a bridge) and the durometer do not interfere with the flexing of the break like most tools on the market do. This allows you to open the break by leverage- simply turn the pressure bolt to increase or reduce the flex. Most systems will require manual flexing by hand of the break and legs with a probe because the holding structure is not able to flex the break open properly or control the flex. Cups that are too stiff and too close to the injector will hamper the tools flexing of the break by creating opposing forces of opening (compression, pushing down) and closing (tension, pulling up) on the break which, will cause the cracks nearest to the injector to fill slower and will end up being under-filled. An under-filled leg or section will separate from the glass from cold temperature. If it is a leg of a star-break it can crack-out.
This windshield repair tool is also used at the point of a long crack and can also slide/straddle down a long crack. This is a 6-in-1 tool. It can be split into a crack-opener and a long crack sliding structure and every other tool on our Crackmaster Tool Page.
NOTE: All Ultra Bond resins are moisture resistant -no dry vacuum is needed. Ultra Bond resins are the only resins proven to restore to new glass strength and beyond. See our homepage. "Why Use Ultra Bond".
Repair Tip
-Technique to prevent any waste of resin. Cure under pressure, then loosen the leveling bolt and injector cylinder slightly. Then loosen the piston by turning it 1/4 to 1/2 turn counterclockwise, slide the screwdriver under the suction cups to remove from the glass. Turn your tool upside down and place the cap on the injector. There will about 1/2 drop if resin in the pit. You can use that resin for a pit-filler if the impact chip was small.
The bridge can be split into three more tools - a crack  opener, long crack slider and single bar chip repair tool and a star-leg flexor.
(2) Crack Opener
The secret to easy long crack repair
Symmetrically opens the crack without spreading it
Creates an overfill
Being a wonder bar it can be reconfigured into three other tools
The secret to easy long crack repair with Ultra Bond structural adhesives is the crack opener. Take it from the Crackmaster himself, size matters with a crack-opener.
The dimensions and custom made suction cups will symmetrically open the crack so you can get our structural adhesive crack resin into the point area of a long crack easily without spreading the crack. Symmetrically opens the crack and creates an overfill. You will see resin come out of the top of the crack when you release the pressure bolt which is what you want. Fundamental fact of adhesives is to overfill. The best from the one who invented long crack repair.
(3) Long Crack Slider and Single Bar Chip Repair Tool
Self leveling
Injector holds 36 drops of resin
This tool slides along the crack and does not push the crack closed
Enter into the repair vs. replacement market
Change suction cups to the 2-inch stiff or 3-inch cup for chip repairs
5-in1-tool can be configured into five different windshield repair tools
Our Crackmaster long crack repair tool slides along and injects the resin into the crack from the surface. The Crackmaster for long cracks is designed to slide from the tip/point to the edge of the windshield. With the stabilizing bolts it is self-leveling and the pressure is controlled so to not push the crack closed as long cracks are surfaced.  The pressure bolt allows you to temporarily increase pressure while at the drill hole so you can get our 400 crack resin to fill the tapped bullseye and start into the crack. Our injector holds 36 drops of resin.
This tool's design allows for sliding and does not push the crack closed. A windshield is only 5 mm thick. The outer layer you are repairing is only 2 mm thick. It will flex easily. Tools used to repair chips have too much pressure and will flex the glass and push the crack closed so that it will under fill or spot the repair. It boils down to the physics of the tool: length, compression, mechanical advantage, size and durometer of the cups.
The two stabilizing bolts allow for automatic leveling. Just push the cup down, level the injector and your ready to go.
Change the soft suction to cup the  2-inch stiff cup or the 3-inch cup and you have a chip repair tool
(4) Star-Leg Flexor
Often while repairing star-breaks one of more of the legs of the star will not completely fill. Since the beginning of windshield repair the method to get the leg to fill was to press on the leg with a small screwdriver or a probe and hold it until it filled. Well normally your thumb and fingers will start to hurt before the leg fills and you will let go too soon and have to do it again. No more of that, with the Star-Leg Flexor you just place the tip in the leg and turn the pressure bolt until you see it flex and then stop. Then just wait for it to fill,  let the Ultra Bond Star-Leg Flexor do the work for you.
(5) Probe
The edge of one side of the Wonder Bar is sharpened to a point for use as a probe.
(6) UV Light Holder
When you are ready to cure the Wonder Bar also works as a UV light holder.
Please See our the link for Long Crack Repair Resins and Chip Repair Resins for use and descriptions of each resin and "Why use Ultra Bond" for Resin Lab Tests.
This Two Wonder Bar kit includes:"
1 CrackMaster Bridge
1 Quick Turn Stainless Steel Injector w/cap
2 3/4" Stabilizing Bolts
2 1" Stabilizing Bolts
1 1 1/2" Star Flexor Bolt
1 1 1/2" Pressure Bolt
1 Suction Cup Adaptor (T-nut)
1 3" Suction Cup
1 2" Stiff Suction Cup
1 2" Soft Suction Cup
1 ea Resins: 20, 40, 45, 90, 200, 400, 1600, 2400, Rain Resin
1 ea 10ml Injector Syringe: 1600, 2400
1 pk Piston O-rings (12)
1 pk Cylinder O-rings (12)
1 pk Drill Bits (10) Round
1 pk Drill Bits (10) Tapered
1 pk 2" Film Tabs (24)
1 Screwdriver
1 Mirror
1 Injector Cleaning Brush
1 Bullseye Tapper w/needle
1 Glass Cutter
1 Center Punch
1 Tape Measure
1 O-ring Case
1 Scrubby
1 UV Safety Glasses
1 Tweezer
1 Razor Blade Holder
20 Razor Blades
1 Cordless Drill Package
2 UV Curing Lights - (1) 6-inch battery and (1) 8-watt 110 12-inch light
1 Tool box (may vary in style)
1 12v Power Inverter (for the UV light)
Note - This Kit has enough resin for 600 chip repairs and 100 long crack repairs.
Listing and template services provided by inkFrog